July 2012 ROTM Nomination Thread!
#19
Ok, took the obligatory shots, so here you go...
As far as mods, etc...
Obviously, the last pic shows the Ern version of the guage upgrade
Other mods are really not obvious, because I'm into the whole OEM/stock look
Taller Powerbronze windshield for the descerning eye.
Driven D3's for the grips
Givi tail trunk for Mama's security and a little cargo capacity.
That funky bead on the steering stem is a GPS mount.
The **** to the left of that is the thermostat control for my Gerbing gear.
Added a 12 volt power outlet to the right fairing just below the fuse panel
Installed a relay/fuse block for the auxilery wiring I've added for my heated
gear and digital voltage meter, etc
The serious "mods" were in the time, sweat and money restoring it back to stock
from the previous butcher's idea of "Bad ***". Hunting down a stock can and headers,
So I could dump the D&D
replacing the tailsection, since he cut off the plate mount, chain-guards, rear lighting, etc.
And of course, complete re-build of the tubes, front/rear brakes, chain/sprockets,
electrical/charging system, blah, blah, blah.
As far as mods, etc...
Obviously, the last pic shows the Ern version of the guage upgrade
Other mods are really not obvious, because I'm into the whole OEM/stock look
Taller Powerbronze windshield for the descerning eye.
Driven D3's for the grips
Givi tail trunk for Mama's security and a little cargo capacity.
That funky bead on the steering stem is a GPS mount.
The **** to the left of that is the thermostat control for my Gerbing gear.
Added a 12 volt power outlet to the right fairing just below the fuse panel
Installed a relay/fuse block for the auxilery wiring I've added for my heated
gear and digital voltage meter, etc
The serious "mods" were in the time, sweat and money restoring it back to stock
from the previous butcher's idea of "Bad ***". Hunting down a stock can and headers,
So I could dump the D&D
replacing the tailsection, since he cut off the plate mount, chain-guards, rear lighting, etc.
And of course, complete re-build of the tubes, front/rear brakes, chain/sprockets,
electrical/charging system, blah, blah, blah.
#20
Ok, took the obligatory shots, so here you go...
As far as mods, etc...
Obviously, the last pic shows the Ern version of the guage upgrade
Other mods are really not obvious, because I'm into the whole OEM/stock look
Taller Powerbronze windshield for the descerning eye.
Driven D3's for the grips
Givi tail trunk for Mama's security and a little cargo capacity.
That funky bead on the steering stem is a GPS mount.
The **** to the left of that is the thermostat control for my Gerbing gear.
Added a 12 volt power outlet to the right fairing just below the fuse panel
Installed a relay/fuse block for the auxilery wiring I've added for my heated
gear and digital voltage meter, etc
The serious "mods" were in the time, sweat and money restoring it back to stock
from the previous butcher's idea of "Bad ***". Hunting down a stock can and headers,
So I could dump the D&D
replacing the tailsection, since he cut off the plate mount, chain-guards, rear lighting, etc.
And of course, complete re-build of the tubes, front/rear brakes, chain/sprockets,
electrical/charging system, blah, blah, blah.
As far as mods, etc...
Obviously, the last pic shows the Ern version of the guage upgrade
Other mods are really not obvious, because I'm into the whole OEM/stock look
Taller Powerbronze windshield for the descerning eye.
Driven D3's for the grips
Givi tail trunk for Mama's security and a little cargo capacity.
That funky bead on the steering stem is a GPS mount.
The **** to the left of that is the thermostat control for my Gerbing gear.
Added a 12 volt power outlet to the right fairing just below the fuse panel
Installed a relay/fuse block for the auxilery wiring I've added for my heated
gear and digital voltage meter, etc
The serious "mods" were in the time, sweat and money restoring it back to stock
from the previous butcher's idea of "Bad ***". Hunting down a stock can and headers,
So I could dump the D&D
replacing the tailsection, since he cut off the plate mount, chain-guards, rear lighting, etc.
And of course, complete re-build of the tubes, front/rear brakes, chain/sprockets,
electrical/charging system, blah, blah, blah.
I'll second that. I think the grill mesh would look better flat black...or hot pink. Your choice!